Flex Twist, Flex Only & Seamless Flexible Waveguide (WG10 to WG23 / WR284 to WR22)

Our flexible waveguides are designed to isolate vibration, eliminate installation difficulties caused by misalignment and to provide a simple aid to positioning and alignment of antennas. Both flexible/twist and flexible... Read full description

SKU: flextwist/flexonly/seamless

Categories: Waveguides

Our flexible waveguides are designed to isolate vibration, eliminate installation difficulties caused by misalignment and to provide a simple aid to positioning and alignment of antennas.

Both flexible/twist and flexible only are made from a helically wound waveguide core and additional mechanical support is offered from a variety of protective jackets.
Long lengths (>1m) of flexible waveguide are not recommended as better performance will be obtained from a mixture of rigid waveguide and much shorter flexible sections - see also hybrid waveguides

 

Preformed and hybrid flexible waveguide assemblies

A preformed waveguide assembly is formed into the desired shape during the manufacturing process. Preforming can reduce the stress on the waveguide and the joints, and it is recommended in waveguides that will be bent close to the minimum static bend radius.

Preforming may be carried out on all GIW Flexible Waveguides and on Side Seam and Seamless waveguides. If a permanent twist is required the GIW Flexible Only Waveguides may be manufactured with a set twist. Preformed waveguides offer a defined and measured electrical performance for the installed shape.

A Hybrid waveguide run can contain both rigid and flexible sections. Flangeless low profile joints offer the following advantages:

  • eliminate EMC issues associated with flange interfaces
  • gas tight joints
  • Lower overall mass and lower profile
  • Lower insertion loss

Wherever possible formed sections will be used in preference to cast or machined sections to ensure the best possible insertion loss and match specifications.

Both preformed and hybrid waveguides can be supplied on a keeper plate, if required, to maintain the shape during storage / shipping.

Jacketing of Preformed and hybrid waveguides

In some cases, it is possible to use hot pressure cured rubbers to jacket waveguides that have been preformed, but this will require specific mould tooling. Where this is not desirable a range of cold cure jackets are available.

Hybrid waveguide with preformed flexible section

Hybrid waveguide with preformed flexible section

Preformed flexible waveguides

Preformed flexible waveguides

Core Types

Flexible / Twistable and Flexible Only core is manufactured by a process of helical winding a silver coated, brass strip to form a continuous, uniform rectangular tube.

Flex twist core

Flex/Twist

Flexible/Twistable is sealed electrically via a friction joint. This construction has the best twistable performance of all our waveguides. The Twistable waveguide will hold limited pressure, but relies on the jacket for pressure sealing. Flex/Twist is not recommended for low PIM applications - use our seamless core.

Flex twist diagram

Flex/Only

Flexible Only core is wound with a solder fillet in the Interlock, thus eliminating any RF and Pressure Leakage. Flex/Only will flex in the E and H planes only, although pre-set twists can be incorporated during manufacture. It is more flexible than seamless.

Flex only diagram

Seamless

This is manufactured by convoluting and forming a metal tube so it will flex in the E and H planes only. Seamless offers the best PIM performance when used in conjunction with the appropriate flanges.

Seemless flex

Side Seam

This is similar in construction to seamless but made from sheet and brazed together.

Operating Temperature Ranges

The table shown below gives the thermal characteristics for the different core types.

Core type Operating temperature range
Flexible / Twistable -55 to +145
Flexible / only -55 to +145
Seamless Brass / BeCu -55 to +145
Side seam silver plated -55 to +145
Side seam Brass / BeCu -70 to +260

As standard, high melting point lead free solder is used to attach the flanges (operating temperature range -55 to +181). Silver solder (operating temperature range -196 to +254) may also be used in some applications.

Jacket Types

We offer a range of different protective coverings to suit most requirements.

Vulcanised Jackets

Neoprene, silicone, and high conductivity silicone jackets are vulcanized to the waveguide using thermal compression techniques and have a high resistance to ozone attack. The jacket provides support to the convolutions during flexing and the pressure seal in Flexible / Twistable waveguides. Neoprene is the standard jackets for our flexible waveguides.

Flex section example

Cold Cure Jackets

Where preformed flexible waveguides are required or vulcanizing is not viable, we offer a variety of cold cure jackets in both silicone or (Urethane) Devcon.

Enamel or epoxy painting may be offered as an alternative to a moulded jacket if required, but should be offered only after consulting the factory.

Operating Temperature Ranges

When operating at elevated temperatures, care should be taken to ensure that the correct jackets and solders have been requested.

The table shown below gives the thermal characteristics for the different jackets available with our flexible waveguides.

Jacket type Operating temperature range Environmental protection
Neoprene -55 to +100 Oil, Ozone
Silicone -70 to 200 Skydrol
Fluoro Silicone -100 to +200 Skydrol
Cold Cure Silicone -65 to +260 Good environmental
Cold Cure Urethane, Devcon -25 to +100 Good environmental

For more details and prices please use the product enquiry form or contact our sales team.

Specifications

Download the Flex Twist, Flex Only & Seamless Flexible Waveguide (WG10 to WG23 / WR284 to WR22) specifications.

06c_waveguide_flexible_2.0a_new.pdf

Enquire

Add your details below to find out more about this product. We'll aim to get back to within 48 working hours.